pavement

PPPOE, access point

From FreeBSDwiki
(Difference between revisions)
Jump to: navigation, search
(Installation and Configuration)
(PPPOE)
Line 14: Line 14:
 
<pre>sshd_enable="YES"</pre>
 
<pre>sshd_enable="YES"</pre>
 
===PPPOE===
 
===PPPOE===
This part can be difficult but we need internet working before following the installation
+
This part can be difficult but we need internet working before following the installation<br>
 +
here's my configuration file:
 +
default:
 +
  set log Phase Chat LCP IPCP CCP tun command
 +
  ident user-ppp VERSION (built COMPILATIONDATE) 
 +
 
 +
  # Ensure that "device" references the correct serial port
 +
  # for your modem. (cuaa0 = COM1, cuaa1 = COM2)
 +
  #
 +
  set device /dev/cuaa1
 +
 +
  set speed 115200
 +
  set dial "ABORT BUSY ABORT NO\\sCARRIER TIMEOUT 5 \
 +
            \"\" AT OK-AT-OK ATE1Q0 OK \\dATDT\\T TIMEOUT 40 CONNECT"
 +
  set timeout 180                        # 3 minute idle timer (the default)
 +
  enable dns                            # request DNS info (for resolv.conf)
 +
 +
 +
alice:
 +
  disable ipv6cp
 +
  add default HISADDR
 +
  set device PPPoE:rl1
 +
  set log Phase tun command
 +
  set ifaddr 10.0.0.1/0 10.0.0.2/0
 +
  set MRU 1490
 +
  set MTU 1490
 +
  # set log Phase tun command
 +
  set authname username@alice.it
 +
  set authkey password
 +
  set dial
 +
  set login
 +
  set cd 5
 +
  set redial 0 0
 +
  set lqrperiod 5
 +
  enable dns
 +
  enable tcpmssfixup
 +
  enable lqr
 +
  #nat enable yes
 +
  #nat use_sockets yes
 +
  #nat unregistered_only yes
 +
note the space at the beginning of the lines,<br>
 +
<i>here you must change the interface that is rl1 in this line:</i>
 +
set device PPPoE:rl1
 +
i disabled ipv6 because it is not needed and messages error were comming in my logs about it,here's the line:
 +
disable ipv6cp
 +
that is realy the lines that are in my configuration: that's because of my provider(alice from italy)...
 +
set authname username@alice.it
 +
set authkey password
 +
you can also optionally change the name alice in this line:
 +
alice:
 +
 
 +
if you do not have it add theses 2 line in /etc/syslog.conf:
 +
!ppp
 +
*.*                                            /var/log/ppp.log
 +
that would permit you to see your log in a separate file that are in /var/log/ppp.log and /var/log/ppp.log.0.bz2(it get created when ppp.log is full, you can see it with bzcat)

Revision as of 17:34, 4 June 2008

Contents

Introduction

Some internet services provider such as alice in italy have a box(alice gate) that does everything(such as router and access point)...unfortunately we want to offer services to the internet such as:

  • ssh
  • web server
  • port redirection for various applications such as games server(such as wormux that needs an open port in order to serve),or p2p

Fortunately the alice gate let us connect directly to the internet: see here for how to deactivate the router functions and so be connected directly to the internet...

The hardware

For my setup, and the instructions included here, I used the same hardware as in AccessPoint that is to say:

  • 2 Realtech PCI 10/100 cards, on FreeBSD. These cards are recognized as rl0 and rl1. (Perhaps there is the possibility to use interfaces aliasing, but as i had 2 cards...)
  • 1 Ralink rt2500 PCI card, on FreeBSD. This card is recognized as ral0.

Installation and Configuration

  • Install FreeBSD as usual. This example uses FreeBSD 7.0.
  • Enable ssh logins during the installation, or add the following line to your /etc/rc.conf:
sshd_enable="YES"

PPPOE

This part can be difficult but we need internet working before following the installation
here's my configuration file:

default:
 set log Phase Chat LCP IPCP CCP tun command
 ident user-ppp VERSION (built COMPILATIONDATE)  
 
 # Ensure that "device" references the correct serial port
 # for your modem. (cuaa0 = COM1, cuaa1 = COM2)
 #
 set device /dev/cuaa1 

 set speed 115200
 set dial "ABORT BUSY ABORT NO\\sCARRIER TIMEOUT 5 \
           \"\" AT OK-AT-OK ATE1Q0 OK \\dATDT\\T TIMEOUT 40 CONNECT"
 set timeout 180                        # 3 minute idle timer (the default)
 enable dns                             # request DNS info (for resolv.conf) 


alice:
 disable ipv6cp
 add default HISADDR
 set device PPPoE:rl1
 set log Phase tun command
 set ifaddr 10.0.0.1/0 10.0.0.2/0
 set MRU 1490
 set MTU 1490
 # set log Phase tun command
 set authname username@alice.it
 set authkey password
 set dial
 set login
 set cd 5
 set redial 0 0
 set lqrperiod 5
 enable dns
 enable tcpmssfixup
 enable lqr
 #nat enable yes
 #nat use_sockets yes
 #nat unregistered_only yes

note the space at the beginning of the lines,
here you must change the interface that is rl1 in this line:

set device PPPoE:rl1

i disabled ipv6 because it is not needed and messages error were comming in my logs about it,here's the line:

disable ipv6cp

that is realy the lines that are in my configuration: that's because of my provider(alice from italy)...

set authname username@alice.it
set authkey password

you can also optionally change the name alice in this line:

alice:

if you do not have it add theses 2 line in /etc/syslog.conf:

!ppp
*.*                                             /var/log/ppp.log

that would permit you to see your log in a separate file that are in /var/log/ppp.log and /var/log/ppp.log.0.bz2(it get created when ppp.log is full, you can see it with bzcat)

Personal tools