Network Configuration (manual)
From FreeBSDwiki
(Difference between revisions)
(changing your network with ifconfig) |
m (Reverted edits by 207.248.164.198 (Talk); changed back to last version by Jimbo) |
||
| (2 intermediate revisions by 2 users not shown) | |||
| Line 5: | Line 5: | ||
options=8<VLAN_MTU> | options=8<VLAN_MTU> | ||
inet6 fe80::290:96ff:fe18:bb9e%dc0 prefixlen 64 scopeid 0x1 | inet6 fe80::290:96ff:fe18:bb9e%dc0 prefixlen 64 scopeid 0x1 | ||
| − | inet 192.168.1.101 netmask 0xfffffff00 broadcast 192.168. | + | inet 192.168.1.101 netmask 0xfffffff00 broadcast 192.168.1.255 |
ether 00:90:96:18:bb9e | ether 00:90:96:18:bb9e | ||
media: Ethernet autoselect (100baseTX <full-duplex>) | media: Ethernet autoselect (100baseTX <full-duplex>) | ||
status: active | status: active | ||
| − | + | from here you can see my inet address is 192.168.1.101; my network requires that I'm on the 192.168.0.0/24 network. So I change my dc0 settings: | |
# ifconfig dc0 down | # ifconfig dc0 down | ||
# ifconfig dc0 192.168.0.101 netmask 255.255.255.0 broadcast 192.168.0.255 up | # ifconfig dc0 192.168.0.101 netmask 255.255.255.0 broadcast 192.168.0.255 up | ||
| Line 20: | Line 20: | ||
options=8<VLAN_MTU> | options=8<VLAN_MTU> | ||
inet6 fe80::290:96ff:fe18:bb9e%dc0 prefixlen 64 scopeid 0x1 | inet6 fe80::290:96ff:fe18:bb9e%dc0 prefixlen 64 scopeid 0x1 | ||
| − | inet 192.168. | + | inet 192.168.0.101 netmask 0xfffffff00 broadcast 192.168.0.255 |
ether 00:90:96:18:bb9e | ether 00:90:96:18:bb9e | ||
media: Ethernet autoselect (100baseTX <full-duplex>) | media: Ethernet autoselect (100baseTX <full-duplex>) | ||
Latest revision as of 14:32, 25 October 2007
The quick and dirty way, when you're in a hurry and want to test settings:
# ifconfig dc0
dc0: flags=108843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
options=8<VLAN_MTU>
inet6 fe80::290:96ff:fe18:bb9e%dc0 prefixlen 64 scopeid 0x1
inet 192.168.1.101 netmask 0xfffffff00 broadcast 192.168.1.255
ether 00:90:96:18:bb9e
media: Ethernet autoselect (100baseTX <full-duplex>)
status: active
from here you can see my inet address is 192.168.1.101; my network requires that I'm on the 192.168.0.0/24 network. So I change my dc0 settings:
# ifconfig dc0 down # ifconfig dc0 192.168.0.101 netmask 255.255.255.0 broadcast 192.168.0.255 up
and my settings change:
# ifconfig dc0
dc0: flags=108843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
options=8<VLAN_MTU>
inet6 fe80::290:96ff:fe18:bb9e%dc0 prefixlen 64 scopeid 0x1
inet 192.168.0.101 netmask 0xfffffff00 broadcast 192.168.0.255
ether 00:90:96:18:bb9e
media: Ethernet autoselect (100baseTX <full-duplex>)
status: active
Since I brought my interface down, made the changes and specified that the state be UP when I changed it, I should be able to ping stuff on the 192.168.0.0/24 network (assuming that my switch/hub/router connection is right etc.) with no problems.
