AccessPoint

Revision as of 17:11, 31 May 2008 (view source) GNUtoo (Talk | contribs) ← Older edit		Revision as of 17:14, 31 May 2008 (view source) GNUtoo (Talk | contribs) (→Nat and firewall) Newer edit →
Line 102:		Line 102:
	natd_interface="rl0"		natd_interface="rl0"
	natd_flags=""		natd_flags=""
		+	if you wish to redirect ports add this to natd_flags="" in /etc/rc.conf:
		+	-redirect_port tcp 192.168.0.6:80 80
	now normally the access point should work...		now normally the access point should work...

---

Revision as of 17:14, 31 May 2008

Contents 1 Introduction 2 The hardware 3 The installation and configuration 3.1 Wireless 3.2 dns and dhcp 4 Nat and firewall

Introduction

FreeBSD is very well suited to be used as an access point,because it has out of the box support of the master mode for a variety of cards such as ralink,atheros cards. Under GNU/Linux you have to:

• use a kernel that is not out yet(2.6.26-rc4)
• patch the kernel with the patch named allow-ap-vlan-modes.patch from http://johannes.sipsolutions.net/patches/kernel/all/LATEST/
• compile a recent libnl(i used libnl-1.1-r1 in gentoo) against the kernel
• in gentoo you need to copy nl80211.h from your kenrel directory to /usr/include/linux
• then finally you need to compile a git version of hostapd...

at the end i got a system that is working with broadcom not ralink ones(made my computer freeze) only in order to have the wifi card working as access point... under FreeBSD it's a lot more easy and more stable(we don't use git or patches)

The hardware

i used:

• 2 realtech pci 10/100 cards,in FreeBSD they are recognized as rl0 and rl1(maybe there is the possibility to use interfaces aliasing but as i had 2 cards...)
• a ralink rt2500 pci card,in FreeBSD it's recognized as ral0

The installation and configuration

• install FreeBSD as usual(i used FreeBSD 7.0)
• enable ssh logins during the installation or add this in your /etc/rc.conf:

sshd_enable="YES"

• if you have got a dhcp modem you can use add the following in your /etc/rc.conf(remplacing ral0 by your wired card interface name)

ifconfig_rl0="DHCP"

otherwise we'll see pppoe later...

Wireless

• then type the following command as root(remplacing ral0 by your wifi card interface name):

ifconfig ral0 inet 192.168.1.1 netmask 255.255.255.0 ssid freebsdap mediaopt hostap channel 4

note that in the FreeBSD handbook inet is placed incorrectly,pay also attention to the channel 4...i tried it without it and it didn't work then try to associate with a client running an operating system such as *BSD or GNU/Linux and ping it: if something goes wrong(ping doesn't work) simply type dmesg and look for message about your wifi card(such as associations messages) under GNU/Linux type as root(remplacing wlan0 by your wifi card interface name):

ifconfig wlan0 up
iwlist wlan0 scan
iwconfig wlan0 essid "freebsdap"
ifconfig wlan0 192.168.1.100 netmask 255.255.255.0
ping 192.168.1.1

under FreeBSD type as root(remplacing ral0 by your wifi card interface name):

ifconfig ral0 up
ifconfig ral0 list scan
ifconfig ral0 inet 192.168.1.100 netmask 255.255.255.0 ssid freebsdap
ping 192.168.1.1

then if you can see the wireless and can ping it simply add the following to /etc/rc.conf:

ifconfig_ral0="inet 192.168.1.1 netmask 255.255.255.0 ssid freebsdap mediaopt hostap channel 4"

dns and dhcp

your wireless is now working...so we can install a dns and dhcp server... for simplicity we will use dnsmasq type the following as root:

cd /usr/ports/dns/dnsmasq
make config

then unselect ipv6 unless you need it and unselect dbus because we won't use it then type the following as root:

make
make install

then we will need to configure dnsmasq: edit /usr/local/etc/dnsmasq.conf with your favorite editor and add the following:

# filter what we send upstream
domain-needed
bogus-priv
filterwin2k
localise-queries

# allow /etc/hosts and dhcp lookups via *.lan
local=/lan/
domain=workgroup
expand-hosts
#resolv-file=/tmp/resolv.conf.auto

dhcp-authoritative
#dhcp-leasefile=/tmp/dhcp.leases

# use /etc/ethers for static hosts; same format as --dhcp-host
# <hwaddr> <ipaddr>
read-ethers

# other useful options:
# default route(s):
dhcp-option=3,192.168.1.1
#    dns server(s):
dhcp-option=6,192.168.1.1

dhcp-range=192.168.1.100,192.168.1.255,255.255.255.0,12h

the file don't need to be explained but read-ethers... read ethers permit you to assign static ip to certain mac address so edit /etc/ethers with entries like this:

00:14:85:11:EF:02 192.168.1.106

and in order to give a dns name to this entry edit /etc/hosts and add an entry like this:

192.168.1.106 Ralink

then in order to start your dnsmasq server at boot you need to add the following to /etc/rc.conf: dnsmasq_enable="YES"

you can now test the wifi connection with any graphical tool(like NetworkManager in GNU/linux or even test it with a windows computer) you can even try to ping a website...but you will only get his ip and no response...that's because we didn't set up the NAT yet...

Nat and firewall

in order to set the nat we will add this to /etc/rc.conf:(remplacing ral0 by your wired card(that is connected to the internet) interface name)::

gateway_enable="YES"
firewall_enable="YES"
firewall_type="OPEN"
natd_enable="YES"
natd_interface="rl0"
natd_flags=""

if you wish to redirect ports add this to natd_flags="" in /etc/rc.conf:

-redirect_port tcp 192.168.0.6:80 80

now normally the access point should work...